Ask a fitter what torque they’ve just put on a flange bolt with a hydraulic wrench and they’ll give you a number. They didn’t read it off the wrench, though. There’s nothing on it to read. They read a pressure off the pump, found it on a chart, and took the chart’s word for it. Hydraulic torque wrench calibration has to cover both sides of that. Is the wrench giving what the chart says at each pressure? Is the gauge showing the pressure that’s really in the hose? If either answer’s no, so is every bolt on the job.
The second half is the one that gets forgotten. The wrench goes off for calibration with a proper certificate, while the pump that drives it has been sitting on the same gauge for years.
How pressure becomes torque
The physics is simple enough. Pump oil into the cylinder and it shoves a piston. The piston turns a ratchet on a lever of fixed length. Twice the pressure, roughly twice the torque. Makers test this for every model and print it as a table for whoever’s on the pump.
Atlas Copco’s published chart for its RTX-18 wrench shows how it looks. 138 bar on it is 5,172 Nm. 414 bar is 15,517 Nm. Go all the way to 690 bar, or 10,000 psi, and it’s 25,861 Nm, which is about 37.5 Nm a bar. There’s a line of small print at the bottom, and it’s the bit we’d want every site to read. The values, it says, “are only applicable when using a calibrated RTX-18 hydraulic torque wrench powered by a 10,000 psi pump fitted with a calibrated class 1 gauge.”
The chart’s maker is telling you outright that the gauge is part of the measurement.
What a class 1 gauge actually allows
A gauge’s accuracy class is a percentage of its full scale, not of the reading. WIKA, one of the biggest gauge makers, explains it this way: on a 0 to 100 bar gauge of class 1.0, the reading may be out by up to 1 bar anywhere on the dial.
Now put that on a pump. A 10,000 psi gauge runs to about 690 bar, so a class 1 gauge that’s perfectly within its class can still be 6.9 bar out. On the RTX-18 chart, 6.9 bar is about 259 Nm.
At the top of the range, 259 Nm on 25,861 Nm is about 1%. Nobody would lose sleep over that. But wrenches don’t spend their lives at the top of the range. Set the same wrench to 5,172 Nm (138 bar) and that same 259 Nm is 5% of what you asked for. That’s from a gauge that would pass its own class.
And that’s before the wrench adds anything. Makers commonly quote hydraulic wrenches at around ±3% (as Maxpro sets out here). So on a low setting, a perfectly “in spec” wrench and gauge can between them be a long way from the figure on your joint procedure. A gauge that’s drifted out of class, been dropped, or had a pressure spike makes that worse, and you won’t see it on the dial. The needle still moves smoothly and still comes back to zero.
When the wrench is fine and the bolt load isn’t
A certificate for the wrench tells you the pressure to torque relationship is right. It doesn’t tell you the gauge on the pump you use with it is reading true.
There’s a practical catch on site too. Pumps get swapped between wrenches all the time. The wrench’s chart travels with the wrench, but the gauge stays on the pump, so the gauge you’re reading on Tuesday may not be the one you read on Monday. If one of the pumps in the store has a gauge nobody’s checked, the wrench certificate doesn’t cover you.
Hex Technology, a bolting tool maker, puts it simply in its guide to how a hydraulic torque wrench works: there are two elements that need calibrating, the wrench itself and the gauge on the hydraulic pump, and both should be done at least once every 12 months. It also says the wrench should be recalibrated after any maintenance, with a new torque chart produced.
The standard people quote, and why it doesn’t fit
You’ll often see ISO 6789 mentioned whenever torque wrenches come up. It’s the right standard for click wrenches and dial wrenches, and it’s the one we work to on torque wrench calibration for those tools. But its full title is ISO 6789-1:2017, Assembly tools for screws and nuts, Hand torque tools. A hydraulic wrench isn’t a hand torque tool, so a certificate claiming ISO 6789 for one should make you ask what was actually done.
A good certificate for a hydraulic wrench lists every pressure it was tested at, with the torque a traceable transducer measured at each, before and after any adjustment. No reference listed? Then you can’t tell what it was checked against. Our guide to traceability in calibration explains why that’s a problem, and there’s more in how to read a calibration certificate.
Hydraulic torque wrench calibration: getting both halves checked
GNW has been calibrating instruments since 1974, and pressure gauges are a core part of that work. We use hydraulic, pneumatic and oil free methods to suit the gauge. Our certificates show readings on rising and falling pressure, so you can see if the gauge sticks or lags as well as where it sits. That’s the same pressure gauge calibration service that covers the gauge on your pump. We calibrate hydraulic torque wrenches too, so both halves of the system can be checked by the same people.
If you’re sending a wrench in, send the pump gauge with it, or tell us which pumps it’s used with. Some teams use torque multipliers on the same joints. If yours do, our torque multiplier calibration checks those on ratio and output.
How often does a hydraulic torque wrench need calibrating?
We’d say yearly as a floor, and do the pump gauge alongside it. Bring both in sooner after any repair or service on the wrench, a dropped pump, a burst hose or a pressure spike. Heavily used tools may need a shorter interval. Our post on how often to calibrate a torque wrench explains how to set one from the tool’s own history.
Do I need to calibrate the pump gauge as well as the wrench?
Yes. The wrench’s chart turns pressure into torque, but you only know the pressure from the gauge. Atlas Copco’s chart for the RTX-18 says its torque values only apply with a calibrated class 1 gauge on the pump.
How accurate is a hydraulic torque wrench?
Makers commonly quote around ±3% for the wrench. The gauge adds its own error on top, which is a fixed amount in bar, so it matters most at low settings. On a 10,000 psi class 1 gauge, that can be about 5% of the reading at the bottom of a wrench’s range.
We share pumps between wrenches. Is that a problem?
It can be. The chart travels with the wrench while the gauge stays bolted to the pump, so every gauge in the pool needs a current certificate. Each pump also has to be one the wrench is designed to run on.
Does ISO 6789 apply to hydraulic wrenches?
No. ISO 6789 covers hand torque tools, such as click and dial wrenches. A hydraulic wrench should be tested at set pressures against a traceable torque transducer, with the results shown point by point on the certificate.
Hydraulic wrench or torque multiplier: what’s the difference?
A multiplier is a gearbox. You put torque in with a hand wrench and get several times more out. A hydraulic wrench uses oil pressure from a pump. Both need calibrating, but a multiplier is checked on its ratio, while a hydraulic wrench is checked on its pressure to torque chart.
Get a quote
Tell us the make, model and torque range of your wrench, and the pumps it’s used with, and we’ll quote for calibrating the lot. Call us on 01704 536010 or get in touch here.